Easy to learn, you’ll pass the Cisco CCDP 300-101 exam! Free 300-101 dumps

Pass the Cisco CCDP 300-101 exam. “Implementing Cisco IP Routing (ROUTE)”: https://www.leads4pass.com/300-101.html (Total Questions: 870 Q&As). I know you most want to get here for free 300-101 dumps. The latest free 300-101 exam practice questions and 300-101 pdf help you improve your skills and exam experience!

Table of Contents:

Latest Cisco CCDP 300-101 pdf

[PDF] Free Cisco CCDP 300-101 pdf dumps download from Google Drive: https://drive.google.com/open?id=1j9mCWwgGmLhAFwPtVdoDN6mcdrk3CSAk

300-101 ROUTE – Cisco: https://www.cisco.com/c/en/us/training-events/training-certifications/exams/current-list/route2.html

Test your Cisco CCDP 300-101 exam level


Which two commands must you configure in the calling router to support the PPPoE client? (Choose Two) 

A. peer default ipaddress pool 

B. mtu 

C. bba-group pppoe 

D. pppoe enable group 

E. pppoe-clientdialer-pool-number 

Correct Answer: BE 


WHich DHCP option provides a TFTP server that Cisco phones can use to download a configuration? 

A. DHCP Option 66 

B. DHCP Option 68 

C. DHCP Option 82 

D. DHCP Option 57 

Correct Answer: A 


Which condition must be met before two EVN devices can connect ? 

A. One VLAN interface must be configured between devices 

B. An EtherChannel configured with at least two interfaces connected between the devices. 

C. A trunk interface must be configured between devices 

D. A fiber connection must be established betwwrn the devices. 

Correct Answer: C 


Refer to the exhibit.lead4pass 300-101 exam question q4

Which routes from OSPF process 5 are redistributed into EIGRP?
A. E1 and E2 subnets matching access list TO-OSPF
B. E1 and E2 subnets matching prefix list TO-OSPF
C. only E2 subnets matching access list TO-OSPF
D. only E1 subnets matching prefix listTO-OS1
Correct Answer: D

After you review the output of the command show ipv6 interface brief, you see that several IPv6 addresses have the
16-bit hexadecimal value of “FFFE” inserted into the address.Based on this information, what do you conclude about
these IPv6 addresses?
A. IEEE EUI-64 was implemented when assigning IPv6 addresses on the device.
B. The addresses were misconfigured and will not function as intended.
C. IPv6 addresses containing “FFFE” indicate that the address is reserved for multicast
D. The IPv6 universal/local flag (bit 7) was flipped.
E. IPv6 unicast forwarding was enabled, but IPv6 Cisco Express Forwarding was disabled.
Correct Answer: A
Extended Unique Identifier (EUI), as per RFC2373, allows a host to assign iteslf a unique 64-Bit IP Version 6 interface
identify them EUI-64). This feature is a key benefit over IPv4 as it eliminates the need of manual configuration or DHCP
in the world of IPv4. The IPv6 EUI-64 format address is obtained through the 48- bit MAC address. The Mac address is
first separated into two 24-bits, with one being OUI (Organizationally Unique Identifier) and the other being NIC specific.
The 16-bit 0xFFFE is then inserted between these two 24-bits to for the 64-bit EUI address. IEEE has chosen FFFE as
a reserved value which can only appear in EUI-64 generated from the EUI-48 MAC address.
Here is an example showing how the Mac Address is used to generate EUI.
Next, the seventh bit from the left, or the universal/local (U/L) bit, needs to be inverted. This bit identifies whether this
interface identifier is universally or locally administered. If 0, the address is locally administered and if 1, the address is
globally unique. It is worth noticing that in the OUI portion, the globally unique addresses assigned by the IEEE have
always been set to 0 whereas the locally created addresses have 1 configured. Therefore, when the bit is inverted, it
maintains its original scope (global unique address is still global unique and vice versa). The reason for inverting can be
found in RFC4291 section 2.5.1.
Once the above is done, we have a fully functional EUI-64 format address. Reference:

if you configure one router in you network with auto-cost reference bandwidth 100 command, which effect on the data
path is true?
A. the data path remains the same for all links
B. the data path changes for 10Mbps links only
C. the data path changes for all links
D. the data path changes for 10GBPS links only
Correct Answer: A

Which type of address does OSPFv3 use to form neighbor adjacencies and to send LSAs?
A. unicast IPv6 addresses
B. link-local addresses
C. multicast address FF02::5
D. unicast IPv4 addresses
Correct Answer: C

Which type of information is displayed when a network engineer executes the show track 1 command on the router?
A. information about tracking list 1
B. information about the IP route track table.
C. time to next poll for track object 1
D. tracking information statistics.
Correct Answer: A

A network engineer enables OSPF on a Frame Relay WAN connection to various remote sites, but no OSPF
adjacencies come up. Which two actions are solutions for this issue? (Choose two)
A. router#show memory allocating-process table
B. router#show memory dead
C. router#show memory processor statistics
D. router#show memory summary
E. router#show memory events
Correct Answer: AD

A diagram with 3 routers:
H1 (with IPv6 IP and Loopback
R1 (with IP IPv6 and Loopback
R2 (with IP IPv6 and Loopback
Running with EIGRP 100 on both routers and what command you will implement so that you will see the loopback IP of
R2 to be advertised at H1
H1(config t)#router eigrp 100 H1(config t)#no stub only
H1(config t) router eigrp 100 H1(config t)#no stub only
R2(config t)#router eigrp 100 R2(config t)#no stub receive only
R2# router eigrp 100 R2(config t)#no stub only
Correct Answer: C

How can you mitigate fragmentation issues between endpoints separated by a GRE tunnel?
A. PMTU (without “D”)
C. windowing D. ICMP DF bit
Correct Answer: B

What are three reasons to control routing updates via route filtering? (Choose three).
A. to hide certain networks from the rest of the organization
B. for easier implementation
C. to control network overhead on the wire
D. for simple security
E. to prevent adjacencies from forming
Correct Answer: ACD

Users were moved from the local DHCP server to the remote corporate DHCP server. After the move, none of the users
were able to use the network. Which two issues will prevent this setup from working properly? (Choose two)
A. Auto-QoS is blocking DHCP traffic.
B. The DHCP server IP address configuration is missing locally
C. 802.1X is blocking DHCP traffic
D. The broadcast domain is too large for proper DHCP propagation
E. The route to the new DHCP server is missing
Correct Answer: BE

Related 300-101 Popular Exam resources

title pdf youtube 300-101 ROUTE – Cisco lead4pass Lead4Pass Total Questions
Cisco 300-101 lead4pass 300-101 dumps pdf lead4pass 300-101 youtube 300-101 ROUTE – Cisco https://www.leads4pass.com/300-101.html 870 Q&A
Cisco CCDP       https://www.leads4pass.com/300-115.html 1067 Q&A
      https://www.leads4pass.com/300-320.html 685 Q&A

Get Lead4Pass Coupons(12% OFF)

lead4pass coupon

What are the advantages of Lead4pass?

We have a number of Cisco, Microsoft, IBM, CompTIA, and other exam experts. We update exam data throughout the year.
Top exam pass rate! We have a large user base. We are an industry leader! Choose Lead4Pass to pass the exam with ease!

why lead4pass


Free Cisco CCDP 300-101 exam exercise questions and answers,
300-101 pdf and 300-101 video practice questions. These will help you improve your exam experience. I know you want to easily get 300-101 certification! It’s not hard! Experts recommend https://www.leads4pass.com/300-101.html help you easily get certified.